May 19, 2013

Turbo Corn on the Cob


I used to cook corn unhusked in boiling water. Then we acquired a turbo broiler. I thought, if I can grill meat in the broiler, it makes sense that I can grill corn there too. Since then, I have never cooked corn any other way. Now our corn on the cob treats are juicy, tasty, and so addictive.

Here are the steps to cooking the best corn on the cob: 
  1. Purchase raw corn ears that look fresh. Avoid those that have dried husks. Peek into the husks to check that the kernels are plump and not drying out.
    Fresh raw corn
  2. Cut off the tips to remove the hair and the back ends. You might want to use a cleaver to chop off the back end – I twist the scissors around the base of the corn until the stalk is severed enough to allow me to break it off.
    Cut off tips of corn husk.

  3. Place them in the turbo broiler and set the temperature to 450 degrees F. 
    Place corn in turbo broiler.

  4. Cook for 20 minutes.
    Bake corn for 20 minutes.

  5. Enjoy!
    Enjoy juicy, tasty corn on the cob.

Remember: Corn is healthy food. It's what you add to the corn (salt, butter, cheese, mayonnaise, catsup, maple syrup, bacon, pot roast, full rack of ribs, etc.) that makes it unhealthy. Truth.


May 14, 2013

The Hobbit Costume Projects: Fili Vest


I volunteered to build the Fili vest for Nina, a friend who's costuming this Hobbit dwarf, mainly because I wanted to make the scales trim using polymer clay. Much like what I did for the Thorin scalemail shirt for Oneal.

Looking at the official Fili image, I figured I’d have to make roughly 150 scales. I estimated I would need 7-10 pieces of 2-oz brown/copper/beige polymer clay bricks. I also figured I’d require about a yard of 54-inch wide material, preferably faux leather or costume suede. I found everything I needed at a crafts and fabric store and bought them with discount coupons.

I worked on the scales first. I had made a positive and a negative mold of the four different forms, so it was just a matter of pulling 150 positives. Bake, then paint, and done!


Scales for Fili vest made from polymer clay


It was my first time to sew a vest, and my first time to work with suede (definitely more manageable than marine vinyl). So, I was learning as I went along. More like winging it.

Guided by the measurements Nina sent me, I cut a paper pattern. I thought I had it right but after I had cut the fabric, I realized I could’ve done a Dolman sleeve instead of a regular sleeve. That would have been easier to sew, and would’ve looked closer to the Fili original. But, with no extra material to revise my design, I went ahead with what I had already cut.

Costume Suede or Distressed Suede


It was nice working with the costume suede because it doesn’t fray (didn't have to do any serging). And the fabric surface, while feeling a bit plastic-y, does not get tacky under the sewing machine’s pressure foot. I just had to guide the material so that it wouldn’t swerve too much.

Fili vest work in progress 



Fili vest without the scales

As soon as I finished sewing, I laid out the scales to check if I had enough. It turned out that I had made too many because I had counted the scales on the real Fili, without thinking that Nina’s measurements are certainly much smaller.


Attaching scales to the Fili vest

Using super glue, I attached all the scales very carefully. No major mishaps aside from the three times that I tore off a piece of finger skin that had bonded with a clay scale.

Fili Vest by Ruby Bayan Llamas
Fili Vest with natural light.

Fili Vest by Ruby Bayan Llamas
Fili Vest with camera flash.

Overall, it was an easy project – a couple hours for measuring and cutting the pattern and material, maybe three to four hours sewing the vest, and an hour gluing the scales. Preparing the 150 clay scales -- conditioning, shaping, baking, and painting -- probably took the longest in terms of manhours. But you really don’t bother counting the hours when you’re having fun!

The best part of all: bragging rights!

Costuming Vest inspired by Fili of The Hobbit



Fili, Lord Elrond, Thorin Oakenshield costumes by Ruby Bayan

Photo taken at the premier of Desolation of Smaug in Manila, December 2013 with Nina (Fili), Dante (Lord Elrond) and Oneal (Thorin Oakenshield).